config updates

Author: thinkyhead

config/examples/ADIMLab/Granty v1/Configuration.h

@@ -131,11 +131,11 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define BOARD_ULTIMAKER
+  #define MOTHERBOARD BOARD_HJC2560C_REV1
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "ADIMLab Granty v1"
+#define CUSTOM_MACHINE_NAME "ADIMLab Granty v1"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like http://www.uuidgenerator.net/version4
@@ -359,6 +359,7 @@
  *    -1 : thermocouple with AD595
  *     0 : not used
  *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+ *   331 : (3.3V scaled thermistor 1 table)
  *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  *     3 : Mendel-parts thermistor (4.7k pullup)
  *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
@@ -402,7 +403,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
+ * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
@@ -2034,6 +2035,12 @@
 //
 //#define MALYAN_LCD
 
+//
+// LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
+// See Configuration_adv.h for all configuration options.
+//
+//#define LULZBOT_TOUCH_UI
+
 //
 // Third-party or vendor-customized controller interfaces.
 // Sources should be installed in 'src/lcd/extensible_ui'.

config/examples/ADIMLab/Granty v1/Configuration_adv.h

@@ -279,9 +279,10 @@
  */
 //#define USE_CONTROLLER_FAN
 #if ENABLED(USE_CONTROLLER_FAN)
-  //#define CONTROLLER_FAN_PIN -1        // Set a custom pin for the controller fan
-  #define CONTROLLERFAN_SECS 60          // Duration in seconds for the fan to run after all motors are disabled
-  #define CONTROLLERFAN_SPEED 255        // 255 == full speed
+  //#define CONTROLLER_FAN_PIN -1           // Set a custom pin for the controller fan
+  #define CONTROLLERFAN_SECS 60             // Duration in seconds for the fan to run after all motors are disabled
+  #define CONTROLLERFAN_SPEED 255           // 255 == full speed
+  //#define CONTROLLERFAN_SPEED_Z_ONLY 127  // Reduce noise on machines that keep Z enabled
 #endif
 
 // When first starting the main fan, run it at full speed for the
@@ -657,10 +658,10 @@
   #endif
 #endif
 
-// @section extras
+// @section motion
 
-// minimum time in microseconds that a movement needs to take if the buffer is emptied.
-#define DEFAULT_MINSEGMENTTIME        20000
+// Minimum time that a segment needs to take if the buffer is emptied
+#define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
 // If defined the movements slow down when the look ahead buffer is only half full
 #define SLOWDOWN
@@ -850,11 +851,35 @@
   #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
 #endif
 
-// Include a page of printer information in the LCD Main Menu
-//#define LCD_INFO_MENU
-#if ENABLED(LCD_INFO_MENU)
-  //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
-#endif
+#if HAS_LCD_MENU
+
+  // Include a page of printer information in the LCD Main Menu
+  //#define LCD_INFO_MENU
+  #if ENABLED(LCD_INFO_MENU)
+    //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
+  #endif
+
+  // BACK menu items keep the highlight at the top
+  //#define TURBO_BACK_MENU_ITEM
+
+  /**
+   * LED Control Menu
+   * Add LED Control to the LCD menu
+   */
+  //#define LED_CONTROL_MENU
+  #if ENABLED(LED_CONTROL_MENU)
+    #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
+    #if ENABLED(LED_COLOR_PRESETS)
+      #define LED_USER_PRESET_RED        255  // User defined RED value
+      #define LED_USER_PRESET_GREEN      128  // User defined GREEN value
+      #define LED_USER_PRESET_BLUE         0  // User defined BLUE value
+      #define LED_USER_PRESET_WHITE      255  // User defined WHITE value
+      #define LED_USER_PRESET_BRIGHTNESS 255  // User defined intensity
+      //#define LED_USER_PRESET_STARTUP       // Have the printer display the user preset color on startup
+    #endif
+  #endif
+
+#endif // HAS_LCD_MENU
 
 // Scroll a longer status message into view
 #define STATUS_MESSAGE_SCROLLING
@@ -879,23 +904,6 @@
   #endif
 #endif
 
-/**
- * LED Control Menu
- * Enable this feature to add LED Control to the LCD menu
- */
-//#define LED_CONTROL_MENU
-#if ENABLED(LED_CONTROL_MENU)
-  #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
-  #if ENABLED(LED_COLOR_PRESETS)
-    #define LED_USER_PRESET_RED        255  // User defined RED value
-    #define LED_USER_PRESET_GREEN      128  // User defined GREEN value
-    #define LED_USER_PRESET_BLUE         0  // User defined BLUE value
-    #define LED_USER_PRESET_WHITE      255  // User defined WHITE value
-    #define LED_USER_PRESET_BRIGHTNESS 255  // User defined intensity
-    //#define LED_USER_PRESET_STARTUP       // Have the printer display the user preset color on startup
-  #endif
-#endif // LED_CONTROL_MENU
-
 #if ENABLED(SDSUPPORT)
 
   // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
@@ -930,6 +938,7 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN         28 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
+    //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
 
@@ -1134,6 +1143,7 @@
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
   //#define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+  //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
 
   // Frivolous Game Options
   //#define MARLIN_BRICKOUT
@@ -1143,6 +1153,53 @@
 
 #endif // HAS_GRAPHICAL_LCD
 
+//
+// Lulzbot Touch UI
+//
+#if ENABLED(LULZBOT_TOUCH_UI)
+  // Display board used
+  //#define LCD_FTDI_VM800B35A        // FTDI 3.5" with FT800 (320x240)
+  //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
+  //#define LCD_HAOYU_FT800CB         // Haoyu with 4.3" or 5" (480x272)
+  //#define LCD_HAOYU_FT810CB         // Haoyu with 5" (800x480)
+  //#define LCD_ALEPHOBJECTS_CLCD_UI  // Aleph Objects Color LCD UI
+
+  // Correct the resolution if not using the stock TFT panel.
+  //#define TOUCH_UI_320x240
+  //#define TOUCH_UI_480x272
+  //#define TOUCH_UI_800x480
+
+  // Mappings for boards with a standard RepRapDiscount Display connector
+  //#define AO_EXP1_PINMAP    // AlephObjects CLCD UI EXP1 mapping
+  //#define AO_EXP2_PINMAP    // AlephObjects CLCD UI EXP2 mapping
+  //#define CR10_TFT_PINMAP   // Rudolph Riedel's CR10 pin mapping
+  //#define OTHER_PIN_LAYOUT  // Define pins manually below
+  #if ENABLED(OTHER_PIN_LAYOUT)
+    // The pins for CS and MOD_RESET (PD) must be chosen.
+    #define CLCD_MOD_RESET  9
+    #define CLCD_SPI_CS    10
+
+    // If using software SPI, specify pins for SCLK, MOSI, MISO
+    //#define CLCD_USE_SOFT_SPI
+    #if ENABLED(CLCD_USE_SOFT_SPI)
+      #define CLCD_SOFT_SPI_MOSI 11
+      #define CLCD_SOFT_SPI_MISO 12
+      #define CLCD_SOFT_SPI_SCLK 13
+    #endif
+  #endif
+
+  // Display Orientation. An inverted (i.e. upside-down) display
+  // is supported on the FT800. The FT810 and beyond also support
+  // portrait and mirrored orientations.
+  //#define TOUCH_UI_INVERTED
+  //#define TOUCH_UI_PORTRAIT
+  //#define TOUCH_UI_MIRRORED
+
+  // Use a numeric passcode for "Screen lock" keypad.
+  // (recommended for smaller displays)
+  //#define TOUCH_UI_PASSCODE
+#endif
+
 // @section safety
 
 /**
@@ -2242,6 +2299,13 @@
  */
 #define EXTENDED_CAPABILITIES_REPORT
 
+/**
+ * Expected Printer Check
+ * Add the M16 G-code to compare a string to the MACHINE_NAME.
+ * M16 with a non-matching string causes the printer to halt.
+ */
+//#define EXPECTED_PRINTER_CHECK
+
 /**
  * Disable all Volumetric extrusion options
  */
@@ -2296,6 +2360,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *

config/examples/ADIMLab/Granty v2/Configuration.h

@@ -73,7 +73,7 @@
 // User-specified version info of this build to display in [Pronterface, etc] terminal window during
 // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
 // build by the user have been successfully uploaded into firmware.
-#define STRING_CONFIG_H_AUTHOR "(ETE-Design, Granty V2)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "(ETE-Design, Granty v2)" // Who made the changes.
 #define SHOW_BOOTSCREEN
 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
 #define STRING_SPLASH_LINE2 WEBSITE_URL         // will be shown during bootup in line 2
@@ -135,7 +135,7 @@
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-#define CUSTOM_MACHINE_NAME "ADIMLab Granty V2"
+#define CUSTOM_MACHINE_NAME "ADIMLab Granty v2"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like http://www.uuidgenerator.net/version4
@@ -359,6 +359,7 @@
  *    -1 : thermocouple with AD595
  *     0 : not used
  *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+ *   331 : (3.3V scaled thermistor 1 table)
  *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  *     3 : Mendel-parts thermistor (4.7k pullup)
  *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
@@ -402,7 +403,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
+ * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
@@ -2034,6 +2035,12 @@
 //
 //#define MALYAN_LCD
 
+//
+// LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
+// See Configuration_adv.h for all configuration options.
+//
+//#define LULZBOT_TOUCH_UI
+
 //
 // Third-party or vendor-customized controller interfaces.
 // Sources should be installed in 'src/lcd/extensible_ui'.