🧑‍💻 Gather Z clearances

Marlin/Configuration.h

@@ -1402,7 +1402,7 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_CLEARANCE_FOR_HOMING of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
@@ -1730,10 +1730,10 @@
  */
 //#define Z_IDLE_HEIGHT Z_HOME_POS
 
-//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                  // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
+//#define Z_CLEARANCE_FOR_HOMING  4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
 
-//#define Z_AFTER_HOMING  10      // (mm) Height to move to after homing Z
+//#define Z_AFTER_HOMING         10 // (mm) Height to move to after homing Z
 
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]

Marlin/src/gcode/bedlevel/G35.cpp

@@ -98,14 +98,7 @@ void GcodeSuite::G35() {
 
   // Probe all positions
   LOOP_L_N(i, G35_PROBE_COUNT) {
-
-    // In BLTOUCH HS mode, the probe travels in a deployed state.
-    // Users of G35 might have a badly misaligned bed, so raise Z by the
-    // length of the deployed pin (BLTOUCH stroke < 7mm)
-
-    // Unsure if this is even required. The probe seems to lift correctly after probe done.
     const float z_probed_height = probe.probe_at_point(tramming_points[i], PROBE_PT_RAISE, 0, true);
-
     if (isnan(z_probed_height)) {
       SERIAL_ECHOPGM("G35 failed at point ", i + 1, " (");
       SERIAL_ECHOPGM_P((char *)pgm_read_ptr(&tramming_point_name[i]));

Marlin/src/gcode/bedlevel/abl/G29.cpp

@@ -494,20 +494,13 @@ G29_TYPE GcodeSuite::G29() {
     #endif
 
     #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
-      if (!abl.dryrun
-        && (abl.gridSpacing != bedlevel.grid_spacing || abl.probe_position_lf != bedlevel.grid_start)
-      ) {
-        // Reset grid to 0.0 or "not probed". (Also disables ABL)
-        reset_bed_level();
-
-        // Can't re-enable (on error) until the new grid is written
-        abl.reenable = false;
+      if (!abl.dryrun && (abl.gridSpacing != bedlevel.grid_spacing || abl.probe_position_lf != bedlevel.grid_start)) {
+        reset_bed_level();      // Reset grid to 0.0 or "not probed". (Also disables ABL)
+        abl.reenable = false;   // Can't re-enable (on error) until the new grid is written
       }
-
       // Pre-populate local Z values from the stored mesh
       TERN_(IS_KINEMATIC, COPY(abl.z_values, bedlevel.z_values));
-
-    #endif // AUTO_BED_LEVELING_BILINEAR
+    #endif
 
   } // !g29_in_progress
 

Marlin/src/gcode/calibrate/G28.cpp

@@ -399,49 +399,50 @@ void GcodeSuite::G28() {
                  doU = home_all || homeU, doV = home_all || homeV, doW = home_all || homeW
                );
 
+    #if !HAS_Y_AXIS
+      constexpr bool doY = false;
+    #endif
+
     #if HAS_Z_AXIS
+
       UNUSED(needZ); UNUSED(homeZZ);
-    #else
-      constexpr bool doZ = false;
-      #if !HAS_Y_AXIS
-        constexpr bool doY = false;
-      #endif
-    #endif
 
-    // Z may home first, e.g., when homing away from the bed
-    TERN_(HOME_Z_FIRST, if (doZ) homeaxis(Z_AXIS));
+      // Z may home first, e.g., when homing away from the bed
+      TERN_(HOME_Z_FIRST, if (doZ) homeaxis(Z_AXIS));
 
-    // 'R' to specify a specific raise. 'R0' indicates no raise, e.g., for recovery.resume
-    // When 'R0' is used, there should already be adequate clearance, e.g., from homing Z to max.
-    const bool seenR = parser.seenval('R');
+      // 'R' to specify a specific raise. 'R0' indicates no raise, e.g., for recovery.resume
+      // When 'R0' is used, there should already be adequate clearance, e.g., from homing Z to max.
+      const bool seenR = parser.seenval('R');
 
-    // Use raise given by 'R' or Z_HOMING_HEIGHT (above the probe trigger point)
-    float z_homing_height = seenR ? parser.value_linear_units() : Z_HOMING_HEIGHT;
+      // Use raise given by 'R' or Z_CLEARANCE_FOR_HOMING (above the probe trigger point)
+      float z_homing_height = seenR ? parser.value_linear_units() : Z_CLEARANCE_FOR_HOMING;
 
-    // Check for any lateral motion that might require clearance
-    const bool may_skate = seenR || NUM_AXIS_GANG(doX, || doY, || TERN0(Z_SAFE_HOMING, doZ), || doI, || doJ, || doK, || doU, || doV, || doW);
+      // Check for any lateral motion that might require clearance
+      const bool may_skate = seenR || NUM_AXIS_GANG(doX, || doY, || TERN0(Z_SAFE_HOMING, doZ), || doI, || doJ, || doK, || doU, || doV, || doW);
 
-    if (seenR && z_homing_height == 0) {
-      if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("R0 = No Z raise");
-    }
-    else {
-      bool with_probe = ENABLED(HOMING_Z_WITH_PROBE);
-      // Raise above the current Z (which should be synced in the planner)
-      // The "height" for Z is a coordinate. But if Z is not trusted/homed make it relative.
-      if (seenR || !TERN(HOME_AFTER_DEACTIVATE, axis_is_trusted, axis_was_homed)(Z_AXIS)) {
-        z_homing_height += current_position.z;
-        with_probe = false;
+      if (seenR && z_homing_height == 0) {
+        if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("R0 = No Z raise");
       }
+      else {
+        bool with_probe = ENABLED(HOMING_Z_WITH_PROBE);
+        // Raise above the current Z (which should be synced in the planner)
+        // The "height" for Z is a coordinate. But if Z is not trusted/homed make it relative.
+        if (seenR || !TERN(HOME_AFTER_DEACTIVATE, axis_is_trusted, axis_was_homed)(Z_AXIS)) {
+          z_homing_height += current_position.z;
+          with_probe = false;
+        }
 
-      if (may_skate) {
-        // Apply Z clearance before doing any lateral motion
-        if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("Raise Z before homing:");
-        do_z_clearance(z_homing_height, with_probe);
+        if (may_skate) {
+          // Apply Z clearance before doing any lateral motion
+          if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("Raise Z before homing:");
+          do_z_clearance(z_homing_height, with_probe);
+        }
       }
-    }
 
-    // Init BLTouch ahead of any lateral motion, even if not homing with the probe
-    TERN_(BLTOUCH, if (may_skate) bltouch.init());
+      // Init BLTouch ahead of any lateral motion, even if not homing with the probe
+      TERN_(BLTOUCH, if (may_skate) bltouch.init());
+
+    #endif // HAS_Z_AXIS
 
     // Diagonal move first if both are homing
     TERN_(QUICK_HOME, if (doX && doY) quick_home_xy());
@@ -497,11 +498,14 @@ void GcodeSuite::G28() {
     TERN_(IMPROVE_HOMING_RELIABILITY, end_slow_homing(saved_motion_state));
 
     #if ENABLED(FOAMCUTTER_XYUV)
-      // skip homing of unused Z axis for foamcutters
+
+      // Skip homing of unused Z axis for foamcutters
       if (doZ) set_axis_is_at_home(Z_AXIS);
-    #else
+
+    #elif HAS_Z_AXIS
+
       // Home Z last if homing towards the bed
-      #if HAS_Z_AXIS && DISABLED(HOME_Z_FIRST)
+      #if DISABLED(HOME_Z_FIRST)
         if (doZ) {
           #if EITHER(Z_MULTI_ENDSTOPS, Z_STEPPER_AUTO_ALIGN)
             stepper.set_all_z_lock(false);
@@ -513,7 +517,7 @@ void GcodeSuite::G28() {
           #else
             homeaxis(Z_AXIS);
           #endif
-          probe.move_z_after_homing();
+          do_move_after_z_homing();
         }
       #endif
 
@@ -525,7 +529,8 @@ void GcodeSuite::G28() {
         if (doV) homeaxis(V_AXIS),
         if (doW) homeaxis(W_AXIS)
       );
-    #endif
+
+    #endif // HAS_Z_AXIS
 
     sync_plan_position();
 
@@ -629,7 +634,7 @@ void GcodeSuite::G28() {
 
   report_current_position();
 
-  if (ENABLED(NANODLP_Z_SYNC) && (doZ || ENABLED(NANODLP_ALL_AXIS)))
+  if (BOTH(NANODLP_Z_SYNC, NANODLP_ALL_AXIS) || TERN0(HAS_Z_AXIS, doZ))
     SERIAL_ECHOLNPGM(STR_Z_MOVE_COMP);
 
   TERN_(FULL_REPORT_TO_HOST_FEATURE, set_and_report_grblstate(old_grblstate));

Marlin/src/inc/Conditionals_post.h

@@ -3180,24 +3180,24 @@
 #endif
 
 /**
- * Z_HOMING_HEIGHT / Z_CLEARANCE_BETWEEN_PROBES
+ * Z_CLEARANCE_FOR_HOMING / Z_CLEARANCE_BETWEEN_PROBES
  */
-#ifndef Z_HOMING_HEIGHT
+#ifndef Z_CLEARANCE_FOR_HOMING
   #ifdef Z_CLEARANCE_BETWEEN_PROBES
-    #define Z_HOMING_HEIGHT Z_CLEARANCE_BETWEEN_PROBES
+    #define Z_CLEARANCE_FOR_HOMING Z_CLEARANCE_BETWEEN_PROBES
   #else
-    #define Z_HOMING_HEIGHT 0
+    #define Z_CLEARANCE_FOR_HOMING 0
   #endif
 #endif
 
 #if PROBE_SELECTED
   #ifndef Z_CLEARANCE_BETWEEN_PROBES
-    #define Z_CLEARANCE_BETWEEN_PROBES Z_HOMING_HEIGHT
+    #define Z_CLEARANCE_BETWEEN_PROBES Z_CLEARANCE_FOR_HOMING
   #endif
-  #if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT
+  #if Z_CLEARANCE_BETWEEN_PROBES > Z_CLEARANCE_FOR_HOMING
     #define Z_CLEARANCE_BETWEEN_MANUAL_PROBES Z_CLEARANCE_BETWEEN_PROBES
   #else
-    #define Z_CLEARANCE_BETWEEN_MANUAL_PROBES Z_HOMING_HEIGHT
+    #define Z_CLEARANCE_BETWEEN_MANUAL_PROBES Z_CLEARANCE_FOR_HOMING
   #endif
   #ifndef Z_CLEARANCE_MULTI_PROBE
     #define Z_CLEARANCE_MULTI_PROBE Z_CLEARANCE_BETWEEN_PROBES

Marlin/src/inc/SanityCheck.h

@@ -214,9 +214,11 @@
 #elif defined(PID_ADD_EXTRUSION_RATE)
   #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default."
 #elif defined(Z_RAISE_BEFORE_HOMING)
-  #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT."
+  #error "Z_RAISE_BEFORE_HOMING is now Z_CLEARANCE_FOR_HOMING."
 #elif defined(MIN_Z_HEIGHT_FOR_HOMING)
-  #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT."
+  #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_CLEARANCE_FOR_HOMING."
+#elif defined(Z_HOMING_HEIGHT)
+  #error "Z_HOMING_HEIGHT is now Z_CLEARANCE_FOR_HOMING."
 #elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
   #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE and Z_AFTER_PROBING instead."
 #elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
@@ -1945,8 +1947,8 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE, "Movement bounds (X_MIN_POS, X_MAX_POS
       #error "TOUCH_MI_PROBE requires TOUCH_MI_RETRACT_Z."
     #elif defined(Z_AFTER_PROBING)
       #error "TOUCH_MI_PROBE requires Z_AFTER_PROBING to be disabled."
-    #elif Z_HOMING_HEIGHT < 10
-      #error "TOUCH_MI_PROBE requires Z_HOMING_HEIGHT >= 10."
+    #elif Z_CLEARANCE_FOR_HOMING < 10
+      #error "TOUCH_MI_PROBE requires Z_CLEARANCE_FOR_HOMING >= 10."
     #elif DISABLED(BABYSTEP_ZPROBE_OFFSET)
       #error "TOUCH_MI_PROBE requires BABYSTEPPING with BABYSTEP_ZPROBE_OFFSET."
     #elif !HAS_RESUME_CONTINUE

Marlin/src/lcd/extui/mks_ui/draw_z_offset_wizard.cpp

@@ -102,20 +102,20 @@ static void event_handler(lv_obj_t *obj, lv_event_t event) {
       current_position.z = z_offset_ref;  // Set Z to z_offset_ref, as we can expect it is at probe height
       probe.offset.z = calculated_z_offset;
       sync_plan_position();
-      // Raise Z as if it was homed
-      do_z_clearance(Z_POST_CLEARANCE);
+      do_z_post_clearance();
       hal.watchdog_refresh();
       draw_return_ui();
       return;
     case ID_M_RETURN:
       probe.offset.z = z_offset_backup;
       SET_SOFT_ENDSTOP_LOOSE(false);
       TERN_(HAS_LEVELING, set_bed_leveling_enabled(mks_leveling_was_active));
+      // On cancel the Z position needs correction
       #if HOMING_Z_WITH_PROBE && defined(PROBE_OFFSET_WIZARD_START_Z)
-        set_axis_never_homed(Z_AXIS); // On cancel the Z position needs correction
+        set_axis_never_homed(Z_AXIS);
         queue.inject_P(PSTR("G28Z"));
-      #else // Otherwise do a Z clearance move like after Homing
-        do_z_clearance(Z_POST_CLEARANCE);
+      #else
+        do_z_post_clearance();
       #endif
       hal.watchdog_refresh();
       draw_return_ui();

Marlin/src/lcd/menu/menu_probe_offset.cpp

@@ -44,10 +44,6 @@ void _goto_manual_move_z(const_float_t);
 // Global storage
 float z_offset_backup, calculated_z_offset, z_offset_ref;
 
-inline void z_clearance_move() {
-  do_z_clearance(Z_POST_CLEARANCE);
-}
-
 void set_offset_and_go_back(const_float_t z) {
   probe.offset.z = z;
   SET_SOFT_ENDSTOP_LOOSE(false);
@@ -75,17 +71,17 @@ void probe_offset_wizard_menu() {
     set_offset_and_go_back(calculated_z_offset);
     current_position.z = z_offset_ref;  // Set Z to z_offset_ref, as we can expect it is at probe height
     sync_plan_position();
-    z_clearance_move();                 // Raise Z as if it was homed
+    do_z_post_clearance();
   });
 
   ACTION_ITEM(MSG_BUTTON_CANCEL, []{
     set_offset_and_go_back(z_offset_backup);
-    // If wizard-homing was done by probe with PROBE_OFFSET_WIZARD_START_Z
+    // On cancel the Z position needs correction
     #if HOMING_Z_WITH_PROBE && defined(PROBE_OFFSET_WIZARD_START_Z)
-      set_axis_never_homed(Z_AXIS); // On cancel the Z position needs correction
+      set_axis_never_homed(Z_AXIS);
       queue.inject(F("G28Z"));
-    #else // Otherwise do a Z clearance move like after Homing
-      z_clearance_move();
+    #else
+      do_z_post_clearance();
     #endif
   });
 

Marlin/src/module/motion.cpp

@@ -38,6 +38,10 @@
   #include "../lcd/marlinui.h"
 #endif
 
+#if ALL(DWIN_LCD_PROUI, INDIVIDUAL_AXIS_HOMING_SUBMENU, MESH_BED_LEVELING)
+  #include "../lcd/e3v2/proui/dwin.h"
+#endif
+
 #if ENABLED(POLAR)
   #include "polar.h"
 #endif
@@ -795,6 +799,14 @@ void do_blocking_move_to_x(const_float_t rx, const_feedRate_t fr_mm_s/*=0.0*/) {
     if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("do_z_clearance_by(", zclear, ")");
     do_z_clearance(current_position.z + zclear, false);
   }
+  void do_move_after_z_homing() {
+    DEBUG_SECTION(mzah, "do_move_after_z_homing", DEBUGGING(LEVELING));
+    #if defined(Z_AFTER_HOMING) || ALL(DWIN_LCD_PROUI, INDIVIDUAL_AXIS_HOMING_SUBMENU, MESH_BED_LEVELING)
+      do_z_clearance(Z_POST_CLEARANCE, true, true);
+    #elif ENABLED(USE_PROBE_FOR_Z_HOMING)
+      probe.move_z_after_probing();
+    #endif
+  }
 #endif
 
 //
@@ -803,13 +815,10 @@ void do_blocking_move_to_x(const_float_t rx, const_feedRate_t fr_mm_s/*=0.0*/) {
 //
 static float saved_feedrate_mm_s;
 static int16_t saved_feedrate_percentage;
-void remember_feedrate_and_scaling() {
-  if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("remember_feedrate_and_scaling: fr=", feedrate_mm_s, " ", feedrate_percentage, "%");
+void remember_feedrate_scaling_off() {
+  if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("remember_feedrate_scaling_off: fr=", feedrate_mm_s, " ", feedrate_percentage, "%");
   saved_feedrate_mm_s = feedrate_mm_s;
   saved_feedrate_percentage = feedrate_percentage;
-}
-void remember_feedrate_scaling_off() {
-  remember_feedrate_and_scaling();
   feedrate_percentage = 100;
 }
 void restore_feedrate_and_scaling() {

Marlin/src/module/motion.h

@@ -398,13 +398,21 @@ void do_blocking_move_to_x(const_float_t rx, const_feedRate_t fr_mm_s=0.0f);
   FORCE_INLINE void do_blocking_move_to_xy_z(const xyze_pos_t &raw, const_float_t z, const_feedRate_t fr_mm_s=0.0f) { do_blocking_move_to_xy_z(xy_pos_t(raw), z, fr_mm_s); }
 #endif
 
-void remember_feedrate_and_scaling();
 void remember_feedrate_scaling_off();
 void restore_feedrate_and_scaling();
 
 #if HAS_Z_AXIS
+  #if ALL(DWIN_LCD_PROUI, INDIVIDUAL_AXIS_HOMING_SUBMENU, MESH_BED_LEVELING)
+    #define Z_POST_CLEARANCE HMI_data.z_after_homing
+  #elif defined(Z_AFTER_HOMING)
+    #define Z_POST_CLEARANCE Z_AFTER_HOMING
+  #else
+    #define Z_POST_CLEARANCE Z_CLEARANCE_FOR_HOMING
+  #endif
   void do_z_clearance(const_float_t zclear, const bool with_probe=true, const bool lower_allowed=false);
   void do_z_clearance_by(const_float_t zclear);
+  void do_move_after_z_homing();
+  inline void do_z_post_clearance() { do_z_clearance(Z_POST_CLEARANCE); }
 #else
   inline void do_z_clearance(float, bool=true, bool=false) {}
   inline void do_z_clearance_by(float) {}